618 idle notebook, hardware reuse, group thousand yuan 1L small host
This content comes from @ worth buying the app, and the view only represents the author. | Author: 鸽 咕 咕
Since I set a ITX small chassis, more grass, keypads, small chassis, small XX, etc. for small concepts, and the volume and small things are even more self-extricted. Some time ago, in the browsing the community, it was grained in the process of 1L small host. When I saw the volume, I felt that the trough is so small. And it is understood that it is basically able to get a machine with a performance enough at a lower price, so look at the old notebook in my handbox, idle hard drive, mouse, keyboard, why don’t you play? . And Intel 3 generation to 9 generations is supportable, the difference is the price.
So, with the current resources and budgets (less than 1000), it is basically only from 4 to the 4th generation.
I basically read the article about 1L host on the 1L host, just to find similar configuration or the same configuration you want, I think I want to go to 8 generations, because I have used 4 generations of 4130, the performance is quite poor, and 6-7 The price is much more expensive, but performance is improved. In addition, if the small chassis also pursues the ultimate performance, that heat dissipation and power consumption have no way to compromise, so I finally selected 4670T.
From the table, you can see that the four generations of CPU prices are between 100-400, using DDR3 memory, with M2 network card interface, some M2 hard disk bits but are all SATA protocols, and then continue to visit.
My demand is a 2.5 hard disk (idle), an NV protocol M2 interface hard disk bit (idle), support 4 generation CPU, use DDR3 memory (from notebook), M2 network port (with AX200, can be changed later .
It is consistent with me during browsing, so I decided that the chassis is HP 800G1DM.
Clearing the chassis and CPU, the rest is to buy buy, two channels of salty fish or Taobao, the idle fish also wrapped up for 2-3 days, but there is no suitable price, and the trading of other idle fish is more embarrassed in this regard. It is also compared to the price, almost the case of choice Taobao. If there is any problem, you can take the property insurance return, so choose Taobao.
In the browsing process, there are also many people to get on the bus, so I selected the store in some comment districts, buy buy, and finally 430 to take the chassis, 300 to win the CPU, total 730 yuan.
I haven’t confirmed receipt yet, but it has been determined everything is normal. In addition, I can see the 800G1 I bought is a WiFi, power supply and brush NV. The power supply is definitely brought, although if there is an idle notebook, I don’t buy it, but my idle notebook interface is not a round, and it is also a WiFi. I heard that I haven’t bought it without WiFi, so I still have wifi, and NV is too lazy to toss, I bought it directly.
Motherboard: HP Q87
Memory: Lenovo DDR3L-1600 4G + Zhaizhai DDR3L-1600 4G
Graphics card: HD4600
Hard disk: Toshiba Q series 128g + Haikang Wei C2000 PRO 512G
Chassis: HP 800G1DM
Total: 730 yuan
This stuff gets the hand really can’t imagine the small, small and exquisite feeling, but the weight is not light in the case of no accessories, and the power supply is actually still more laborious. There are 2 USB3.0 interfaces and 1 headset hole, 1 headset hole.
There is a power outlet, a network port, a 4 USB3.0 interface, an audio input interface, a VGA interface, and 2 DP interfaces, which is still complete for a small host.
There are 2 increasing ribs at the bottom, and there are 2 non-slip mats, and there are several nameplates and some basic information, nothing special.
Contrast other objects, and the shell IPAD mini4 is almost magnitude, better than two G304, so it is really small.
Note the previously upgraded notebook to the two 4G DDR3L memory strips ready.
Old ancient Dongzhi Q series MLC, 128G, used for 6 years to estimate, all kinds of equipment, eventually idle, because the interface has problems, the SATA interface is broken with only metal contacts, and the capacity is too small.
AX200 is scheduled, before I want to experience WiFi6 installed on the plate, now there is a network card with ITX chassis, so it is still idle.
Haikang Weiwei C2000 PRO, 10 years of quality assurance, but recently, in this Toshiba particle, there is no need to use the West number 1T, this is idle, after all, M2 is not much.
Ready. Oh, I forgot that there is a CPU.
I5-4670T, the color is generally scratched.
After the screws that are unscrew the tail, you can see it in front of the front end of the chassis, and you can see it. You can see what the memory bracket is under the hard disk bracket, so it is necessary to remove the hard disk bracket.
Second step demolition hard disk bracket
Unscrew 3 hard drive screws easy to remove the memory slot and wireless network card, the right side is the SATA interface and fan interface, and the split fan needs to pull the fan.
The NIC is 7260, and it is still a difference.
There is a small yellow dot on the motherboard, which is a clear BIOS button, which is equivalent to the buckle buckle.
Third step refolding radiator
The heat sink has three screws, screwed in sequence, similar to the heat dissipation of the notebook, screwed out, no fixed position.
After opening, you can see the CPU and the cooling fan.
Check if there is any problem with the pin, there is no problem.
The fan is 12V0.95A, the speed is still very high, and the high speed takes off like sitting on the helicopter. There are 4 screws on the fan, continue to be removed. Basically the entire motherboard is exposed, and the other M2 interface is also under the fan.
Fourth stepped CPU, M2 solid state and memory
For the mouth of the quasi-CPU, do not force the miracle, the interface is not equal to the problem.
M2 interface, arrange, and worry that there is a cooling vest without installing the fan, and it is found that I have more concern, there is no problem.
The CPU is buckled, the M2 solid state, the memory is installed, and the heat sink is applied.
Note: Be sure to confirm that the memory has been completely accepted, I stepped on this pit.
Take out my own heat and silver silicone fat, now 1600X is still used, and the problem is not big.
Apply uniform and get it.
The fifth step is reduced by heat dissipation
Install the fan, get a cool heat, look at the post is not fit.
Remove the fan power line.
Sixth step to install SATA solid state
Previously opened the cover to see 4 blue things were wrapped up and stick to the motherboard, the four blue things were used to fix the SATA solid. All twice, feel a little fun, a car?
Usage is the patch of the expenses, let the hard disk slide into the track, but also need to use it, it is the same, but this looks into the chassis is not right, or needs to fix the hard disk first. Otherwise, there are 2 screws that can not be screwed.
Screw the screw directly to the good screw.
Then I should be caught, but here the motherboard SATA mouth blocks the road to press down, the hard pressure is going to do, so put the motherboard SATA, put it out, put the hard disk and plug it back.
The final subsequent.
Power on the power.
After the installation, the fan was found directly at the highest speed. The reason was unknown, the temperature rose, and then tried to change the memory, clear the BIOS, and later the fan was normal, but the monitor did not signal, ask the customer service to toss for a long time, choose to give up, all demolished Plan return. The next day, get up or not, I don’t know if it is the problem of graphics card wiring. All bring it to the company. The company has a DP mouth and VGA mouth, try again.
Later, the boot fan was still taken off, and the shutdown was turned back and returned. The picture appeared in the VGA mouth, but BIOS had an error, I need to press F1, I have forgotten, 2 reports, one is low power, the other is BIOS Time error. The operation is successfully turned on, because Toshiba is in the notebook, so it is turned on normally.
Later, try the DP interface, which can also be displayed, so there is no problem with the interface, the CPU has no problem, and the memory is no problem (it seems to be not connected). Going back to get off work at home, DP is normal, it is not seen the BIOS picture.
The system and small chassis in the SATA solid state do not match the BIOS error.
BIOS is a bit problem that is turned on.
My monitor is 4K screen, 4 generation u on 4K support is not very good, BIOS itself does not display properly in 4K (here I have appeared in 4130), and then successfully entered the system, pressing the BIOS result screen. Black, press the power button directly to shut down (this and the phenomenon of the BIOS interface or the phenomenon that does not enter the system interface is directly turned on directly).
Therefore, it may be that the SATA SS Solid System and the hardware change in the BIOS cause the BIOS error, and the 4K display cannot display the BIOS, and the fistase is operated at the highest speed until the 1080p operation is returned to normal. 4K friends must pay attention to this. But my idea may be wrong, or ask the big idea to make more professional explanation.
Run a separate look at the temperature
Enter the system uses the HWIDGEN digital activation system.
The next Lu master looks at the configuration
Take a look at the CPU-Z, 45W TDP, quad-core four-thread, I don’t know where to get better than my old notebook.
Run a CPU-Z, a single core 326, a multi-core 1232, a 7600K boss millions.
Run Chess, 17.11 times.
Master Lu runs a bit, and the total division is almost 10W. The performance is still very satisfied, and the writing office is a good choice.
Look at the speed of the M2 interface, compared to normal M2, order and write can do 1200MB / s is very good, more than 800MB / s, 4K, but still incense.
Finally, look at the temperature, up to 61 ° C, with an average of 50 ° C, or very low. At the highest level of 71 ° C, it is relatively high, but it will rarely work all day long. So, it is mainly based on an average 50 ° C.
After a power meter, there will be 50W, which will be about 20W, and there is a low 16W. Then I opened a night for about 7-8 hours, basically standby to sleep, consumes 0.1 degree electricity, so power consumption still makes me very surprised, let me want to do something, then say it later.
Now the 4K screen of the home is normal, can be used normally, but 4K can only 30 frames, and hear that the highest is 40-50 frames, so still decrease the resolution, or use other forms.
In fact, the machine did not think about it, you can go to the wife to go to the Internet, but it is estimated that the wife will rush to use my ITX, it is very uncomfortable, and it is indeed a screen, otherwise it can only be public screen, or Idle.
In fact, I also want to engage in black fruit, so I have made this 1L host. I found that it is true!