The house on the first floor is humid, don’t worry about decoration, there are 3 ways to understand in advance

0 Comments

Hello everyone, I am a homemath that focuses on home and decoration knowledge. If you like it, click the level!

The biggest feature of the first floor house is that it may be humid. Especially some old first -floor houses are very wet. If we find that the house is a house on the first floor and humid, then I personally think that everyone should deal with the two aspects of moisture -proof and dehumidification. First of all, we must prevent the tide from entering our home, and the other is to reduce the humidity of our room. This can basically solve the problem of humid houses to the greatest extent. Therefore, in this article, the home of home miscellaneous altars will answer the humid house on the first floor through the following three aspects.

Do a good job of moisture -proof

一楼房子潮湿,别着急装修,有3种方法要提前了解

As a result, the fundamental reasons that cause the house on the first floor are basically appearing on our walls and ground. Because the ground on the first floor of the traditional first floor is actually the soil directly, and some of our exterior walls are also in contact with the soil. Therefore, if the moisture -proof on the wall and the ground will not be done well, the water vapor in the ground will pass our ground, and it will still be. There is the slow penetration of the wall into our room. But what we do at this time is to prevent moisture, there is no way to do it below the ground or outside the wall. For this reason, I recommend the following moisture -proof treatment methods. The specific treatment method is to infiltrate the crystal of the cement base.

①The method introduction.

The most commonly used method is to use cement base to infiltrate crystallization and waterproof to paint our ground and wall. The specific method is that we need to remove the decorative materials paved or painted on the ground or wall. For example, eliminate the latex paint and putty on the wall to expose the plastering layer inside. Put the ground on the wooden floor or tiles to remove the concrete on the ground.

②, paint cement base penetration crystals.

After we clean up the wall and the ground, we can paint the cement base to penetrate the crystals. Personally, you recommend that you rinse the wall and the ground with water before applying it, and then let the wall and the ground dry it to paint. For the painting of cement base penetration crystals, it must be painted more than three times. In other words, we use hair brushes or rolling brushes on the surface of the wall, and the overall paint on the ground is coated with cement base infiltration crystals.

③ Restore on the ground and wall surface.

一楼房子潮湿,别着急装修,有3种方法要提前了解

When the cement base penetrates the crystals completely dry, we can come to the normal decoration of the walls and grounds of our home. For example, the wall of our home can be scraped directly, and then brushed latex paint. For example, the ground in our house, you can directly spread tiles. If it is a wooden floor, I personally recommend that you apply a layer of cement mortar on the surface of the cement base to penetrate the crystals, and then install the wooden floor.

一楼房子潮湿,别着急装修,有3种方法要提前了解

Indoor decoration should be well -processed

When we decorate, we need to choose some materials with moisture -proof function to decorate our room. Like the first floor of us, because it is more humid, the choice of decoration materials may be different from other floors. For example, our wall, selection of moisture -proof materials, or ground materials, and also choose materials with this function. For this reason, I recommend the following interior decoration and moisture -proof practices, and everyone can understand it.

① The interior wall is used with water -resistant materials.

一楼房子潮湿,别着急装修,有3种方法要提前了解

For example, our interior wall needs to be scraped putty, so at this time, I recommend that everyone must choose water -resistant putty. In fact, we can choose the external wall putty, because the external wall putty has water resistance to prevent mildew and prevention. The only defect is that there are more glue substances. For water -resistant putty scrapes, it must be scraped more than twice, that is, the first time it is dry. After simple treatment, you can batch it for the second time. For facial decoration materials, I personally recommend that you adopt materials with scrubbing function and anti -permeability function. Like some imported latex paint now, the functions in this area are still better.

②, decoration on the ground.

On the ground floor, I personally recommend that you choose to pave the floor tiles as much as possible, and do not need to choose a wooden floor. Because the wooden floor may be deformed after the moisture, and the wooden floor has a certain ability to absorb water, it will cause our indoor mold to be more serious. So we choose to pave the ground tiles directly. For the labing of floor tiles, it is not recommended to adopt dry paving methods. It is recommended that you adopt traditional wet paving methods. The wet paving method is to apply a layer of wet cement mortar on the ground, and then spread floor tiles. Because this approach is far from the perspective of moisture -proof prevention.

一楼房子潮湿,别着急装修,有3种方法要提前了解

③ Treatment of the gap.

In fact, the ground moisture -proof is still very important, that is, the gap treatment of the floor tiles paved on the ground. Although the ground of many homes is also paved with floor tiles, it is found that the tide is serious. Later, it was found that there was no obvious water track in the gaps of the tiles. So we also need to deal with the gap of the tiles here. For this reason, I personally recommend a dedicated flexible sewing agent, or adopt the current commonly used sewing agents, and process all the gaps in our tiles for a beautiful sewing agent.

Demolition indoor dehumidification in time

Because the indoor humidity is caused by the back of our wall or the ground on the ground, but the other side is indeed caused by the high air humidity. Like many parts of our country, the air humidity in the summer is very large, which leads to the exposure of the wall or ground in our room, and these situations will cause the humidity of our room to increase significantly. Therefore, we must timely dehumidify the interior to ensure the indoor effect.

① Install a dedicated dehumidifier.

This dehumidifier is not a common humidifier in our house. Damp -dehomatics, similar to the dehumidifier for heavy industry, can learn about such a dehumidifier. Like a small dehumidifier, the area that can be covered can basically reach 50 ~ 100 square meters, so we buy a dehumidifier according to the area of ​​our ambassador. Wet dehumidification must also learn to install effective installation to ensure that it has a drainage. In this wet season, we turn on the dehumidifier to dehumidify the room, so as to avoid humidity problems that occur in the room due to the large air humidity.

②, reasonably use the dehumidification function of air conditioners.

If we do not install a dedicated dehumidifier in our house, then personal recommendation can reasonably use the dehumidification function brought by the air conditioner in our home. Because almost all air conditioners now have dehumidification function. When our air humidity is particularly large, we can turn on the dehumidification function of the air conditioner, so that the indoor dehumidification can also prevent mold from mold.

一楼房子潮湿,别着急装修,有3种方法要提前了解

③, real -time monitoring the humidity of the room.

一楼房子潮湿,别着急装修,有3种方法要提前了解

Maybe the humidity of many friends in the room is not a special understanding, so I recommend that you install a humidity instrument at home. Like many household thermometers now, it has a humidity measurement function. We buy such a instrument to hang in our room. For example, the humidity of the indoor should be kept at about 40%. If the humidity of the indoor is found to exceed 50%, then this is to be dehumidified in time, so as to avoid the humidity of the indoor cause mold.

一楼房子潮湿,别着急装修,有3种方法要提前了解

Conclusion

For the humid ground on the first floor, everyone should briefly understand the reasons for indoor humidity, and then take effective measures for these reasons. For example, the most fundamental reason is that the most fundamental reason is caused by the poor moisture -proof effect of the indoor wall or ground. Another reason is that the air humidity is large. Therefore, for the humidity of the first -floor houses, individuals briefly introduce everyone in this article the moisture -proof and some moisture -proof materials selected during the decoration. There is also the treatment of humidity. Everyone should try to use dehumidifiers to dehumidify, so as to solve the problem of large indoor humidity from the two aspects. This can prevent our indoor tide and mold.

一楼房子潮湿,别着急装修,有3种方法要提前了解

[Personal original, the picture comes from the Internet, the infringement contact is deleted! .